Can We Interconnect SFP, SFP+, XFP, X2 and XENPAK?

There are many kinds of 10G optical transceivers in the market such as SFP+, XFP, X2 and XENPAK. So when we use these modules, the most confusing problem is if we can interconnect SFP+, XFP, X2 and XENPAK. Besides this, some module users also want to know if they can connect SFP to SFP+ or if then can connect 10GBASE-SR modules to 10GBASE-LR modules. In this article, I will display some common questions often asked by module users and give the right answer mainly based on Cisco optical transceivers.
1. Can we interconnect SFP-10G-SR to XENPAK-10GB-SR or X2-10GB-SR?
The answer is yes. For this problem, you just need the correct optic on each side. If your optics are singlemode you need singlemode patch cord. If your optics are multi-mode then you need multi-mode patch cord. SFP-10G-SR, XENPAK-10GB-SR and X2-10GB-SR are all multi-mode optics, so a multi-mode fiber can solve this problem.
2. Can LC-SC patch cord connect X2-10GB-SR between SFP-10G-SR?
Yes, it’ll work fine as long as your fiber patch cord is multi-mode. Actually, the SFP+ requires LC connector but the X2 may require a SC connector. So when connect SFP-10G-SR to X2-10GB-SR, we must use a LC-SC patch cable (LC connector on one fiber end, SC connector on the other fiber end).
3. Is it possible to connect X2-10GB-LR to SFP-10G-SR?
The answer is not possible. The Cisco X2-10GB-LR module supports a link length of 10 kilometers on standard single-mode fiber (SMF, G.652). However, the Cisco SFP-10G-SR module supports a link length of 300m on OM3 multi-mode fiber (MMF,OM3) and 400m on OM4 multi-mode fiber (MMF,OM4). Actually, you need to use modules with the same wavelengths, i. e. SR to SR or LR to LR.
4. Can we connect SFP-10G-SR to GLC-SX-MM?
The SFP-10G-SR is 10 Gbps only. The GLC-SX-MM is 1 Gbps only. This question means can we force SFP-10G-SR to use 1Gbps speed?  This is a very common question and the response will always be the same. The answer is NO. Because the SFP-10G-SR is 10 Gbps only. It runs at 10 Gbps link rate and no other speed. GBIC, SFP, X2, QSFP, CFP modules will only negotiate to one speed and one speed only. You cannot interconnect them.
5. Can we connect GLC-SX-MM to GLC-LH-SM?
Some users wonder if they can use GLC-SX-MM together with GLC-LH-SM? In fact, the GLC-SX-MM is multi-mode LED-based. The GLC-LH-SM is singlemode laser-based. They may (sometimes) work with mode conditioning patch (MCP) cables but it’s not generally a good idea unless it’s completely unavoidable.
Fiberstore (FS.COM) offers a variety of fiber optic transceivers at very economical prices which can satisfy your requirements from 1G to 100G Ethernet. In addition, all these optical transceivers are in stock and you can enjoy the same day shipping service. For more information, please contact us over sales@fs.com.

评论

发表评论

此博客中的热门博文

What Is VLAN Switch and Why Do We Need It?

图片
VLAN or virtual LAN is a type of LAN that is defined to map workstations based on everything except for geographic location. It develops when the network has increased in size and complexity, and many companies require more access ports or a network design. Basically, it’s a networking technology which allows the network to be segmented logically without geographic restrictions. But how much do you know about VLAN switch? What Is  VLAN Switch? VLAN switch is built on the fiber optic switch  of LAN, which realizes the division and management of logical working group as a software. As defined in IEEE standard 802.1Q, VLAN switch can provide a way to transform one network into multiple broadcast domains. And each broadcast domain is usually matched with IP subnet boundaries, so that each subnet has its own VLAN. Therefore, users can obtain various wired LANs for different purposes that are co-existed physically, which means you don’t need to buy additional hardware or cabling at a la
阅读全文

Differentiate the 3 Technologies: Switch Stacking vs Cascading vs Clustering

图片
When we have more than one switches on hand we often seek to a better way in making use of them and managing them. There are mainly three technologies that we might use when we interconnect or combine several switches together, which are switch stacking, cascading and clustering. For many people that firstly get in touch with these terms, they can’t figure out the differences between them. Some discussions of the switch stacking versus switch clustering and switch stacking versus switch cascading have been put forward, but a comprehensive comparison between them has not been made. So this post is a discussion of switch stacking vs cascading vs clustering. Switch Stacking vs Cascading vs Clustering The comparison of switch stacking, cascading and clustering should be based on knowing the meaning of these technologies. So firstly we will see what switch stacking, cascading and cluster are. What Are Switch Stacking, Cascading and Clustering? Switch stack
阅读全文

Nylon Zip Ties vs Hook-&-Loop (Velcro®) Ties

图片
The confinement system is the last but critical part of the entire cable management systems. Cable tie plays a very important role in this part. However, there are various types of cable ties in the market. Which one is better? Since nylon zip ties and hook-&-loop (Velcro®) ties are most common and controversial. This tutorial will compare these two types of cable ties in details. Overview of Cable Ties Cable ties are cheap and simple components used in cable confinement system. They are usually the last measure to ensure the cable managed in order. Cable ties are available in a variety of sizes and materials for use on different applications with different requirements. In addition, there are various of color options for cable ties. These color codes help users to manage the cabling and achieve easy troubleshooting. The most commonly used formats of cable ties are nylon zip ties and hook-&-loop (Velcro®) ties, as the Figure 1 & 2 shown: Figure 1. Drawing of Nylo
阅读全文