Things We Should Know Before Migrating to Base-8 System

Since the introduction of Base-12 connectivity in the mid 1990s, the 12-fiber MTP/MPO connector and Base-12 connectivity have served the data center for about twenty years. It has helped a lot in achieving high-density and manageable cabling. Recently, many documents and posts are discussing about a new technology—Base-8. Its appearance is regarded as the evident need of future networks. Even though most of the words are promoting the overwhelming advantages of Base-8 system, we should still consider the defects and merits of these two systems based on some facts before taking the next step by ourselves. This post is a discussion on this topic.
Facts of Base-12 and Base-8
In this part, the design features of Base-12 and Base-8 systems will be introduced. And their dominant advantages are going to be discussed too.
Design Features
Base-12 connectivity makes use of links based on groups of 12, with 12-fiber connectors such as the MTP. In Base-12 connectivity, for example, trunk cables have fiber counts that are divisible by number 12, like 24-fiber trunk cable, 48-fiber trunk cable and all the way up to 144 fibers. However, in a Base-8 system, we don’t have 12-fiber trunk cable, instead we have 8-fiber trunk cable, 16-fiber trunk cable, 32-fiber trunk cable and so on. All trunk cables are based on increments of 8 fibers.
Base-12 and Base-8 trunk cables are visually different on connector design. A Base-12 trunk cable generally has unpinned (female) connectors on both ends and demands the use of pinned breakout modules. In the new emerging Base-8 system, a trunk cable is designed with pinned (male) connectors, as a result, it should be connected to unpinned components.
pinned & unpinned connectors
Figure: Unpinned and Pinned Connectors
Comparison
Compared with Base-8, Base-12 obviously has the benefit of higher connector fiber density. Thus a larger number of fibers can be installed more quickly when using Base-12 connectivity. And it is very easy to be deployed into all-ready existing Base-12 architecture. As the networks are migrating to 40G and 100G data speeds, Base-8 connectivity has some advantages that cannot be denied. For some 40G and 100G applications, including SR4 (40G and 100G over parallel MMF) and PSM4 (100G over parallel SMF) supported eight-fiber transceivers, and SAN switch Base-8/Base-16 port arrangements, Base-8 connectivity is a more cost-effective choice. In these applications, Base-8 enables full fiber utilization for eight-fiber transceiver systems. But Base-8 connectivity is not optimized for all situations, including duplex protocols like 25G and 100G (duplex SMF).
Correct Co-existence of Base-8 and Base-12
If we are going to deploy Base-8 devices in our existing network, it is possible to have Base-12 and Base-8 connectivity at the same time as long as we do not mix them in the same link. On one hand, it is not wise to use conversion module between Base-12 and Base-8 devices, because the added cost and increased insertion loss will surpass the benefits it can brought. As mentioned before, the two systems are not interchangeable since they usually have different connector configurations and have unequal attachment requirements. Therefore, special care should be given when managing the data canter physical layer infrastructure, to ensure that the Base-12 and Base-8 components are used separately.
Conclusion
When a new technology comes out as a new option for us, we need to decide whether to change or not. In terms of the discussion on Base-12 and Base-8 systems, after listening to voices from different sides, the key factors are still determined by own specific needs. If we decided to move to the new technology, the following question is how to realize the best migration. Having comprehensive understanding of the solutions and products vendors supply will never be a bad choice.
Originally posted on: https://goo.gl/rITPWa

评论

发表评论

此博客中的热门博文

What Is VLAN Switch and Why Do We Need It?

图片
VLAN or virtual LAN is a type of LAN that is defined to map workstations based on everything except for geographic location. It develops when the network has increased in size and complexity, and many companies require more access ports or a network design. Basically, it’s a networking technology which allows the network to be segmented logically without geographic restrictions. But how much do you know about VLAN switch? What Is  VLAN Switch? VLAN switch is built on the fiber optic switch  of LAN, which realizes the division and management of logical working group as a software. As defined in IEEE standard 802.1Q, VLAN switch can provide a way to transform one network into multiple broadcast domains. And each broadcast domain is usually matched with IP subnet boundaries, so that each subnet has its own VLAN. Therefore, users can obtain various wired LANs for different purposes that are co-existed physically, which means you don’t need to buy additional hardware or c...
阅读全文

Differentiate the 3 Technologies: Switch Stacking vs Cascading vs Clustering

图片
When we have more than one switches on hand we often seek to a better way in making use of them and managing them. There are mainly three technologies that we might use when we interconnect or combine several switches together, which are switch stacking, cascading and clustering. For many people that firstly get in touch with these terms, they can’t figure out the differences between them. Some discussions of the switch stacking versus switch clustering and switch stacking versus switch cascading have been put forward, but a comprehensive comparison between them has not been made. So this post is a discussion of switch stacking vs cascading vs clustering. Switch Stacking vs Cascading vs Clustering The comparison of switch stacking, cascading and clustering should be based on knowing the meaning of these technologies. So firstly we will see what switch stacking, cascading and cluster are. What Are Switch Stacking, Cascading and Clustering? Switch stack...
阅读全文

Nylon Zip Ties vs Hook-&-Loop (Velcro®) Ties

图片
The confinement system is the last but critical part of the entire cable management systems. Cable tie plays a very important role in this part. However, there are various types of cable ties in the market. Which one is better? Since nylon zip ties and hook-&-loop (Velcro®) ties are most common and controversial. This tutorial will compare these two types of cable ties in details. Overview of Cable Ties Cable ties are cheap and simple components used in cable confinement system. They are usually the last measure to ensure the cable managed in order. Cable ties are available in a variety of sizes and materials for use on different applications with different requirements. In addition, there are various of color options for cable ties. These color codes help users to manage the cabling and achieve easy troubleshooting. The most commonly used formats of cable ties are nylon zip ties and hook-&-loop (Velcro®) ties, as the Figure 1 & 2 shown: Figure 1. Drawin...
阅读全文